Digital Electronics(Modern Digital Design)Review what I have and help on a few that I could not figure out(EASY)
micael47
w1_assignment_modern_digital.docxIC Interfacing
Complete the following odd-numbered problems from Chapter 5.
•Pages 190 to 193: 3 – 11, 23 -31, 43 – 51, and 63 – 71
•Odd-numbered problems only – twenty questions
3. Applying 2.4V to a CMOS input (10-V power supply) is interpreted by the IC as a(n)______(HIGH, LOW, undefined) logic level.
5. A “typical” HIGH output voltage for a TTL gate would be about _________3.5V
7. A “typical” HIGH output voltage for a CMOS gate (10-V power supply) would be about___+10____V.
9. Applying 3.0V to a 74HCT00 series CMOS input (5-V power supply) is interpreted by the IC as a(n)________(HIGH, LOW, undefined) logic level.
11. The 74ALVC series of logic ICs are modern _______ (CMOS, TTL) chips.
23. Refer to Fig. 5-47. If both families A and B are ALS-TTL, the inverter (can, may not be able to) drive the AND gates.
27. Generally, ______(CMOS, TTL) ICs consume the least power.
29. The VDD pin on a 4000 series CMOS IC is connected to________(ground, positive) of the dc power supply.
31. Refer to Fig. 5-12. When the switch is open, the _ PULL-UP ____ resistor causes the input of the CMOS inverter to be pulled HIGH.
43. Refer to Fig. 5-25(b). When the input to the inverter goes LOW, its output goes______ (HIGH, LOW) which______ (turns off, turns on) the transistor allowing current to flow through the transistor and piezo buzzer to sound the buzzer.
45. Refer to Fig. 5-27(b). When the input to the inverter goes HIGH, its output goes LOW which_______(turns off, turns on) the NPN transistor; the coil of the relay is ______(activated, deactivated), the armature of the relay______(clicks, will not click) downward and the solenoid_______ (is, will not be) activated.
47. Refer to Fig. 5-28(b). If the input to the inverter goes HIGH, its output goes LOW which_____(activates, deactivates) the LED, the phototransistor is_______(turned off, turned on), and the output voltage goes_________(HIGH, LOW).
49. Refer to Fig. 5-28(d). This is an example of good design practice by using an optoisolator to isolate the low-voltage digital circuit from the higher-voltage noisy motor circuit. (T or F)
51. A solid-state relay is a close relative of the optoisolator. (T or F)
63. Hall-effect devices such as gear-tooth sensors and switches are commonly used in automobiles because they are rugged, reliable, operate under sever conditions and are inexpensive. (T or F)
65. Refer to Fig. 5-50. Moving the magnet closer to the Hall-effect sensor increases the strength of the magnetic field which causes the output voltage to _______(decrease, increase).
67. Refer to Fig. 5-51. If the IC is the bipolar 3132 Hall-effect switch, then the ______(N, S) pole of the magnet will turn the device on while the _______(N, S) pole will turn the output transistor off.
69. Refer to Fig. 5-50. The output of this device is _________(analog, digital) in nature.
71. Refer to Fig. 5-45. The BASIC Stamp 2________(Audio-amplifier, Microcontroller) Module substitutes as a PWM generator to rotate the servo motor.
FIG 5-47
FIG 5-8(b)
FIG 5-12
FIG 5-25(b)
FIG 5-27(b)
FIG 5-28(b)
FIG 5-28(d)
FIG 5-50
FIG 5-51
