# Engineering Aeronautical Engineering Homework

**DBlaylock1979**

I will pay top dollar for the completion of questions 1-6 in the attached document.

- a year ago
- 100

**files (1)**

## AERO_309_Module_4_HW.docx_safe.pdf

## AERO_309_Module_4_HW.docx_safe.pdf

College of Aeronautics | worldwide.erau.edu

All rights are reserved. The material contained herein is the copyright property of Embry-Riddle Aeronautical University, Daytona Beach, Florida, 32114. No part of this material may be reproduced, stored in a retrieval system or transmitted in any form, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of the University.

AERO 309 - Module 4 Homework

1. In the book and presentations, we used dimensional analysis to derive the expression

L=q∞Scl. Now use dimensional analysis to derive M=q∞Sccm. 2. Use the following airfoils from the back of the book: NACA 1412, NACA 2412, NACA

4412, NACA 0006, and NACA 0009. For this question, use the airfoil data that is closest to a Reynolds number of 6 million. Make sure you are using the correct curve. DO NOT use the “Standard roughness” or flap curves.

a. For each airfoil, what is the maximum percent camber, the location of the maximum camber, and the maximum percent thickness?

b. Using the airfoil data in the back of the book, what is the αL=0, cl at α=0, and cm at α=0 for each airfoil?

c. From the information in (b), what can you say about the effect of camber? What is special about the lift and moment for the symmetric airfoils?

d. For the symmetric airfoils, use the data in the back of the book to find clmax and αstall.

e. From the information in (d), what is the effect of thickness on the lift curve? 3. Use the provided pressure coefficient distribution and Excel

a. Plot the Cp distribution. Make sure to use the convention where the Cp axis is flipped (i.e. the negative Cp values are above the x-axis). Include your name in the

plot title.

b. Find the minimum (most negative) Cp value. c. Use the trapezoidal rule to find cl. Since the chord length in the provided

distribution is 1, the integral to find cl is simplified. cl=∫01Cp,l dx-∫01Cp,u dx d. Explain the steps you took in (c) in using the trapezoidal rule to find cl

4. Using the minimum Cp from the last question and Excel a. Let the minimum Cp from earlier be Cp,0. Use the Prandtl-Glauert rule to plot Cp from M∞=0 to M∞=0.8 with a maximum interval of ΔM=0.01. Include your name in the

plot title.

b. On the same plot, add the Cp,cr equation from the book and presentation from M∞=0.4 to M∞=0.8

c. From the plot, what is Mcr and Cp,cr of the airfoil (to the closest 0.01 Mach)? 5. Reduce the magnitude of the minimum Cp from the previous question by 30% (multiply by

0.7). Now use the iterative method to find Mcr and Cp,cr 6. Assume you have a supersonic airfoil at M∞=1.75

a. If the airfoil has the same cl as the one you found in question 3, what is the angle of attack α in radians and degrees?

b. What is the wave drag coefficient cdw?

**other Questions(10)**

- Complete the Closing Case "Motivating Employees at the SAS Institute" in Ch. 6 of Understanding and Managing Organizational Behavior.
- Does income make us happier and healthier?
- write an essay
- Anyone on here a C# programmer?
- A-Plus Writer
- imagine that you have been approved to participate in a cooperative program. indicate where you would like to work and...
- SWOT and Strategy Evaluation Paper
- Resources Short Essay
- Mutants
- CJS 230 Week 9 Final Project Community Corrections