Packet Tracer - Skills Integration Challenge
Addressing Table (10pts) ( 1.25 pts for each. 8 blanks)
Device
Interface
IP Address
Subnet Mask
ASw-1
VLAN 1
10.10.10.100
255.255.255.0
ASw2
VLAN 1
10.10.10.150
255.255.255.0
User-01
NIC
10.10.10.4
255.255.255.0
User-02
NIC
10.10.10.5
255.255.255.0
Objectives
•
Configure hostnames and IP addresses on two Cisco Internetwork Operating System (IOS) switches
using the command-line interface (CLI).
•
Use Cisco IOS commands to specify or limit access to the device configurations.
•
Use IOS commands to save the running configuration.
•
Configure two host devices with IP addresses.
•
Verify connectivity between the two PC end devices.
Scenario
As a recently hired LAN technician, your network manager has asked you to demonstrate your ability to
configure a small LAN. Your tasks include configuring initial settings on two switches using the Cisco IOS and
configuring IP address parameters on host devices to provide end-to-end connectivity. You are to use two
switches and two hosts/PCs on a cabled and powered network.
Requirements (20pts)
Complete each requirement below by entering the commands CLI in the Packet Tracer lab. Fill in the blanks
below. (.625 pts for 10 blanks)
1. Use a console connection to access each switch. (2.5pts)
2. Name ASw-1 . (2.5pts) and ASw-2 . (2.5pts)
switches.
- What command did you use? hostname
3. Use the R4Xe3 password for all lines. . (2.5pts)
- What command did you use? password
4. Use the C4aa secret password. . (2.5pts)
- What command did you use? enable secret
5. Encrypt all clear text passwords. . (2.5pts)
- What command did you use? service password-encryption
6. Include the word warning in the message-of-the-day (MOTD) Banner. . (2.5pts)
- What command did you use? banner motd
7. Configure addressing for all devices according to the Addressing Table.
8. Save your configurations. . (2.5pts)
1.3.1.3 Packet Tracer - Skills Integration Challenge
- What command did you use? wri mem
Note: Click Check Results to see your progress. Click Reset Activity to generate a new set of requirements.
Connectivity Tests (10pts)
Pinging from each to port to each port verifies a functional network, This can be done in the Lab. The lab will
record your pings.
Ping From Device IP
Ping to Device IP
Results
Solutions if Ping Fails
10.10.10.150
10.10.10.100
bytes=32 time=3ms
TTL=255
Cry
10.10.10.150
10.10.10.100
bytes=32 time=11ms
TTL=255
10.10.10.150
10.10.10.100
bytes=32 time=11ms
TTL=255
10.10.10.150
10.10.10.100
bytes=32 time=11ms
TTL=255
PACKET TRACER LAB GRADING RUBRIC
Element
Criteria
None:
Criteria
not met
Some:
Less than
half of the
specified
criteria is
met
Most:
More than
half of the
specified
criteria is
met
All:
All of
the
specified
criteria
is met
Points
Earned
Instructo
r’s
Commen
ts
Requirements
•
Each
requirement/step has
been completed.
0 pts.
1–9 pts.
10–19 pts.
20 pts.
Address Table/
Questions
Answered
•
All address tables
and/or questions
have been answered.
0 pts.
1–4 pts.
5–9 pts.
10 pts.
Configuration/
IP Address
•
Configurations
and/or IP addresses
are correct, creating a
functional network.
0 pts.
1–4 pts.
5–9 pts.
10 pts.
TOTAL
Out of
1.3.1.3 Packet Tracer - Skills Integration Challenge
40 points
