ITCC Skills Final
kephung97
SkillsFinal-KevinVo.docx
CCNA 2 Skills Assessment - SB
CCNA 2 Skills Assessment - SB
Topology
Student Name:
Assessment Objectives
Part 1: Add the devices to Packet Tracer (45 points, 45 minutes)
Part 2: Configure Network Infrastructure Settings (VLANs, Trunking, Etherchannel) (30 points, 25 minutes)
Part 3: Configure Host Support (20 points, 25 minutes)
Part 4: Test and Verify IPv4 and IPv6 End-to-End Connectivity (5 points, 10 minutes)
Scenario
In this Skills Assessment (SA) you will configure the devices in a small network. You must configure a router, switch and PCs to support both IPv4 and IPv6 connectivity for supported hosts. Your router and switch must also be managed securely. You will configure inter-VLAN routing, DHCP, Etherchannel, and port-security.
Packet Tracer Items
1 Router (Cisco 4321)
2 Switches (Cisco 2960)
2 PCs
Ethernet cables as shown in the topology
VLAN Table
|
VLAN |
VLAN Name |
|
2 |
Potato |
|
3 |
Chimichanga |
|
4 |
Management |
|
5 |
Parking |
|
6 |
Native |
Addressing Table
|
Device / Interface |
IP Address / Prefix |
Default Gateway |
|
R1 G0/0/1.2 |
10.19.8.1 /26 |
N/A |
|
R1 G0/0/1.2 |
2001:db8:acad:a::1 /64 |
N/A |
|
R1 G0/0/1.3 |
10.19.8.65 /27 |
N/A |
|
R1 G0/0/1.3 |
2001:db8:acad:b::1 /64 |
N/A |
|
R1 G0/0/1.4 |
10.19.8.97 /29 |
N/A |
|
R1 G0/0/1.4 |
2001:db8:acad:c::1 /64 |
N/A |
|
R1 G0/0/1.6 |
N/A |
N/A |
|
R1 Loopback0 |
209.165.201.1 /27 |
N/A |
|
R1 Loopback0 |
2001:db8:acad:209::1 /64 |
N/A |
|
S1 VLAN 4 |
10.19.8.98 /29 |
10.19.8.97 |
|
S2 VLAN 4 |
10.19.8.99 /29 |
10.19.8.97 |
|
PC-A NIC |
DHCP for IPv4 address |
DHCP for IPv4 default gateway |
|
PC-A NIC |
2001:db8:acad:a::50 /64 |
fe80::1 |
|
PC-B NIC |
DHCP for IPv4 address |
DHCP for IPv4 default gateway |
|
PC-B NIC |
2001:db8:acad:b::50 /64 |
fe80::1 |
Note: There is no interface on the router supporting VLAN 5.
Instructions
Add the Devices to Packet Tracer
Total points: 45
Time: 20 minutes
Add the Devices to Packet Tracer
Start a new Packet Tracer and add the devices in the topology to your Packet Tracer.
Make sure to name your devices!
Configure R1.
Configuration tasks for R1 include the following:
Remember to fill in any blank spaces with the command(s) used.
|
Task |
Specification |
Points |
|
Disable DNS lookup |
|
0.5 pt |
|
Router name |
R1 |
0.5 pt |
|
Domain name |
ccna-lab.com |
0.5 pt |
|
Encrypted privileged EXEC password |
cisco |
1 pt |
|
Console access password |
ciscoconsole |
1 pt |
|
Set the minimum length for passwords |
10 characters |
1 pt |
|
Create an administrative user in the local database |
Username: admin Password: supersecret |
1 pt |
|
Set login on VTY lines to use local database |
|
1 pt |
|
Set VTY lines to accept SSH connections only |
|
1 pt |
|
Encrypt the clear text passwords |
|
1 pt |
|
Configure an MOTD Banner |
|
0.5 pt |
|
Enable IPv6 Routing |
|
1 pt |
|
Configure Interface G0/0/1 and sub interfaces |
Set the description Set the IPv4 address Set the IPv6 Link Local Address as fe80::1 Set the IPv6 address Activate Interface |
4 pts |
|
Configure the Loopback0 interface |
Set the description Set the IPv4 address Set the IPv6 address Set the IPv6 Link Local Address as fe80::1 |
2 pts |
|
Generate an RSA crypto key |
1024 bits modulus |
1 pt |
Configure S1 and S2.
Configuration tasks for the switches include the following:
Remember to fill in any blank spaces with the command(s) used.
|
Task |
Specification |
S1 |
S2 |
|
Disable DNS lookup |
|
0.5pt |
0.5pt |
|
Switch name |
S1 or S2, as appropriate |
0.5pt |
0.5pt |
|
Domain name |
Skills-Final.com |
0.5pt |
0.5pt |
|
Encrypted privileged EXEC password |
cisco |
1pt |
1pt |
|
Console access password |
ciscoconsole |
1pt |
1pt |
|
Create an administrative user in the local database |
Username: admin Password: supersecret |
1pt |
1pt |
|
Set login on VTY lines to use local database |
|
1pt |
1pt |
|
Set VTY lines to accept SSH connections only |
|
1pt |
1pt |
|
Encrypt the clear text passwords |
|
1pt |
1pt |
|
Configure an MOTD Banner |
|
0.5pt |
0.5pt |
|
Generate an RSA crypto key |
1024 bits modulus |
1pt |
1pt |
|
Configure Management Interface (SVI) |
Set the Layer 3 IPv4 address |
2pts |
2pts |
|
Configure Default Gateway |
Configure the default gateway as 10.19.8.97 for IPv4 |
1pt |
1pt |
Configure Network Infrastructure Settings (VLANs, Trunking, EtherChannel)
Total points: 30
Time: 20 minutes
Configure S1.
Configuration tasks for S1 include the following:
|
Task |
Specification |
Points |
|
Create VLANs |
VLAN 2, name Potato VLAN 3, name Chimichanga VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native |
5 points |
|
Create 802.1Q trunks that use the native VLAN 6 |
Interfaces F0/1, F0/2, and F0/5 |
1 point |
|
Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2 |
Use the LACP protocol for negotiation |
2 points |
|
Configure host access port for VLAN 2 |
Interface F0/6 |
1 point |
|
Configure port-security on access ports |
Allow 3 MAC addresses |
2 points |
|
Secure all unused interfaces |
Assign to VLAN 5, Set to access mode, add a description, and shutdown |
4 points |
Configure S2.
Configuration tasks for S2 include the following:
|
Task |
Specification |
Points |
|
Create VLANs |
VLAN 2, name Potato VLAN 3, name Chimichanga VLAN 4, name Management VLAN 5, name Parking VLAN 6, name Native |
5 points |
|
Create 802.1Q trunks that use the native VLAN 6 |
Interfaces F0/1 and F0/2 |
1 point |
|
Create a Layer 2 EtherChannel port group that uses interfaces F0/1 and F0/2 |
Use the LACP protocol for negotiation |
2 points |
|
Configure host access port for VLAN 3 |
Interface F0/18 |
1 point |
|
Configure port-security on access ports |
Allow 3 MAC addresses |
2 points |
|
Secure all unused interfaces |
Assign to VLAN 5, Set to access mode, add a description, and shutdown |
4 points |
Configure Host Support
Total points: 20
Time: 10 minutes
Configure R1
Configuration Tasks for R1 include the following
|
Task |
Specification |
Points |
|
Configure Default Routing |
Create a default routes for IPv4 and IPv6 that direct traffic to interface Loopback 0 |
(4 points) |
|
Configure IPv4 DHCP for VLAN 2 |
Create a DHCP pool for VLAN 2, consisting of the last 10 addresses in the subnet only. Assign the domain name ccna-a.net and specify the default gateway address as the router interface address for the subnet involved |
(6 points) |
|
Configure IPv4 DHCP for VLAN 3 |
Create a DHCP pool for VLAN 3, consisting of the last 10 addresses in the subnet only. Assign the domain name ccna-b.net and specify the default gateway address as the router interface address for the subnet involved |
(6 points) |
Configure host computers.
Configure the host computers PC-A and PC-B to use DHCP for IPv4 and statically assign the IPv6 GUA and Link Local addresses. After configuring each host computer, record the host network settings with the ipconfig /all command.
|
PC-A Network Configuration (2 points) |
|
|
Description |
blank |
|
Physical Address |
blank |
|
IP Address |
blank |
|
Subnet Mask |
blank |
|
Default Gateway |
blank |
|
IPv6 Default Gateway |
blank |
|
PC-B Network Configuration (2 points) |
|
|
Description |
blank |
|
Physical Address |
blank |
|
IP Address |
blank |
|
Subnet Mask |
blank |
|
Default Gateway |
blank |
|
IPv6 Default Gateway |
blank |
Test and Verify End-to-End Connectivity
Total points: 5
Time: 10 minutes
Use the ping command to test IPv4 and IPv6 connectivity between all network devices.
Use the following table to methodically verify connectivity with each network device. Take corrective action to establish connectivity if a test fails:
Remember to fill the Ping Results column with your results.
|
From |
To |
Protocol |
IP Address |
Ping Results |
|
PC-A |
R1, G0/0/1.2 |
IPv4 |
10.19.8.1 |
blank |
|
PC-A |
R1, G0/0/1.2 |
IPv6 |
2001:db8:acad:a::1 |
blank |
|
PC-A |
R1, G0/0/1.3 |
IPv4 |
10.19.8.65 |
blank |
|
PC-A |
R1, G0/0/1.3 |
IPv6 |
2001:db8:acad:b::1 |
blank |
|
PC-A |
R1, G0/0/1.4 |
IPv4 |
10.19.8.97 |
blank |
|
PC-A |
R1, G0/0/1.4 |
IPv6 |
2001:db8:acad:c::1 |
blank |
|
PC-A |
S1, VLAN 4 |
IPv4 |
10.19.8.98 |
blank |
|
PC-A |
S2, VLAN 4 |
IPv4 |
10.19.8.99. |
blank |
|
PC-A |
PC-B |
IPv4 |
IP address will vary. |
blank |
|
PC-A |
PC-B |
IPv6 |
2001:db8:acad:b::50 |
blank |
|
PC-A |
R1 Loop0 |
IPv4 |
209.165.201.1 |
blank |
|
PC-A |
R1 Loop0 |
IPv6 |
2001:db8:acad:209::1 |
blank |
|
PC-B |
R1 Loop0 |
IPv4 |
209.165.201.1 |
blank |
|
PC-B |
R1 Loop0 |
IPv6 |
2001:db8:acad:209::1 |
blank |
|
PC-B |
R1, G0/0/1.2 |
IPv4 |
10.19.8.1 |
blank |
|
PC-B |
R1, G0/0/1.2 |
IPv6 |
2001:db8:acad:a::1 |
blank |
|
PC-B |
R1, G0/0/1.3 |
IPv4 |
10.19.8.65 |
blank |
|
PC-B |
R1, G0/0/1.3 |
IPv6 |
2001:db8:acad:b::1 |
blank |
|
PC-B |
R1, G0/0/1.4 |
IPv4 |
10.19.8.97 |
blank |
|
PC-B |
R1, G0/0/1.4 |
IPv6 |
2001:db8:acad:c::1 |
blank |
|
PC-B |
S1, VLAN 4 |
IPv4 |
10.19.8.98 |
blank |
|
PC-B |
S2, VLAN 4 |
IPv4 |
10.19.8.99. |
blank |
|
PC-B |
S2, VLAN 4 |
N/A |
N/A |
N/A |
2019 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 6 www.netacad.com
2019 - 2021 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 6 www.netacad.com
