Project Execution

profileVeedish
GauchitoProjectWorkbook.xlsx
Home>Engineering homework help>Electronic Engineering homework help>Project Execution

Deliverables

1.0 ASSEMBLE ENGINE MOUNT
2.0 FIN PREPARATION
3.0 MARK FIN AND LAUNCH LUG LINES
4.0 INSERTING ENGINE MOUNT
5.0 ATTACH FINS
6.0 ATTACH SHOCK CORD
7.0 ASSEMBLE NOSE CONE
8.0 ATTACH PARACHUTE/SHOCK CORD
9.0 ATTACH LAUNCH LUG
10.0 PAINTING THE ROCKET
11.0 APPLICATION OF DECALS
12.0 APPLYING CLEAR COAT
13.0 DISPLAY NOZZLE ASSEMBLY
14.0 ROCKET PREFLIGHT
15.0 PREPARE FOR TEST LAUNCH

TITLE

GAUCHITO ROCKET PROJECT
PROJECT WORKBOOK
Doubleclick to open

Hi-Level WBS

1.0 ASSEMBLE ENGINE MOUNT
1.1 Measure, Mark and Cut Engine Tube
1.2 Cut Engine Tube
1.3 Glue, Tube, Assemble Hook
1.3.1 Apply thin line of glue completely around engine at 3/4" mark
1.3.2 Position Hook per diagram
1.3.3 Insert Engine Hook into 1/8" Slit on Engine Mount Tube
1.4 Assemble Mylar Ring to Tube
1.5 Assemble Yellow Engine Block to Engine Mount Tube
1.6 Assemble Centering Rings
1.7 Application of Glue Fillets
2.0 FIN PREPARATION
2.1 Sand/Cut fins
2.2 Cutting Out Fins
2.3 Stack and Sand Fins
3.0 MARK FIN AND LAUNCH LUG LINES
3.1 Cut Tape
3.2 Remove guide, connect fins and lug lines, extend LL line
3.3 Extend Launch Lug Line
4.0 INSERTING ENGINE MOUNT
4.1 Mark inside of tube @ 5/8" where LL is
4.2 Glue Tube
4.3 Assemble Engine Hook
4.4 Gluing Center Body Ring
5.0 ATTACH FINS
5.1 Attach Fin #1
5.2 Attach Fin #2
5.3 Attach Fin #3
5.4 Attach Fin #4
5.5 Check Fin Alignment
5.6 Allow glue to dry
6.0 ATTACH SHOCK CORD
6.1 Cut out shock cord mount
6.2 First Glue Application
6.3 Second Glue Application
6.4 Squueze and Hold
6.5 Attaching Shock Cord Mount
7.0 ASSEMBLE NOSE CONE
7.1 Glue nose cone
8.0 ATTACH PARACHUTE/SHOCK CORD
8.1 Attach Lines
8.2 Attach Parachute
8.3 Tie Lines
9.0 ATTACH LAUNCH LUG
9.1 Glue launch lines
9.2 Application of Glue Fillets
10.0 PAINTING THE ROCKET
10.1 Apply first coat
10.2 Sand
10.3 Apply final coat
11.0 APPLICATION OF DECALS
11.1 Apply first decal
11.2 Apply second decal
11.3 Apply third decal
11.4 Apply fourth decal
11.5 Apply fifth decal
11.6 Apply sixth Decal
11.7 Apply seventh Decal
12.0 APPLYING CLEAR COAT
12.1 Apply clear coat to entire rocket
13.0 DISPLAY NOZZLE ASSEMBLY
13.1 Spray Nozzle Base White
13.2 Apply Glue
14.0 ROCKET PREFLIGHT
14.1 Prepare Rocket for Preflight
14.2 Spike
14.3 Fold
14.4 Roll
14.5 Reinsert
15.0 PREPARE FOR TEST LAUNCH
15.1 Insert Engine

Activity List

1.0 ASSEMBLE ENGINE MOUNT
1.1 Measure, Mark and Cut Engine Tube
-1.1.1 Lay ruler along engine tube
-1.1.2 Measure engine from left of engine tube tube @ 1/8"
-1.1.3 Mark left end of Engine Tube @ 1/8'
-1.1.4 Measure engine from left of engine tube @ 3/4"
-1.1.5 Mark from left of EngineTube @ 3/4"
-1.1.6 Measure engine tube from left of engine tube @ 11/2"
-1.1.7 Mark from left of Engine Tube @ 1 1/2"
-1.2 Cut Engine Tube
-1.2.1 Cut Slit of 1/8" @ 1 1/2 inch Mark on Engine Tube
-1.3 Glue, Tube, Assemble Hook
-1.3.1 Apply thin line of glue completely around engine at 3/4" mark
-1.3.2 Position Hook per diagram
-1.3.3 Insert Engine Hook into 1/8" Slit on Engine Mount Tube
-1.4 Assemble Mylar Ring to Tube
-1.4.1 Slide Mylar ring onto Engline Mount tube at 3/4" mark
-1.4.2 Let Dry
-1.5 Assemble Yellow Engine Block to Engine Mount Tube
-1.5.1 Apply glue inside front of Engine Mount tube
-1.5.2 Insert Yellow Engine Block flush with the right end per diagram
-1.5.3 Let Dry
-1.6 Assemble Centering Rings
-1.6.1 Remove Centering rings from card with modeling knife
-1.6.2 Apply thin line of Glue around engine mount tube @ 1/8" mark
-1.6.3 Slide notched Centering Ring onto glued line @ 1/8" mark
-1.6.4 Let Glue Set
-1.6.5 Apply thin line of Glue to opposite side of notched center ring flush with end of engine mount tube
-1.6.6 Slide unnotched Centering Ring in place over glue flush with end of engine tube mount
-1.6.7 Let Dry
-1.7 Application of Glue Fillets
-1.7.1 Apply Glue Fillets to both sides of Centering Rings for reinforcement
-1.7.2 Let Dry
2.0 FIN PREPARATION
-2.1 Sand/Cut fins
-2.1.1 Sand Laser Cut Balsa Sheet w/Fine Sandpaper
-2.2 Cutting Out Fins
2.2.1 Cut out fin #1 w/modeling knife
2.2.2 Cut out fin #2 w/modeling knife
2.2.3 Cut out fin #3 w/ modeling knife
2.2.4 Cut out fin #4 w/modeling knife
-2.3 Stack and Sand Fins
-2.3.1 Stack Fins
-2.3.2 Sand Edges of fins
3.0 MARK FIN AND LAUNCH LUG LINES
-3.1 Cut - Tape
3.1.1 Cut out tube marking guide
-3.1.2 Tape tube marking guide around body tube
-3.1.3 Mark body tube at arrows
-3.1.4 Mark Launch Lug Line as LL on Body tube
-3.2 Remove guide, connect fins and lug lines, extend LL line
-3.2.1 Remove Tube Marking guide from body tube
-3.2.2 Connect Fins using door frame
-3.2.3 Connect launch lug lines using door frame
-3.3 Extend Launch Lug Line
-3.3.1 Extend launch lug line 3 3/4" from end of tube
4.0 INSERTING ENGINE MOUNT
-4.1 Mark inside of tube @ 5/8" where LL is
-4.1.1 Measure inside tube to 5/8" position on tube
-4.1.2 Mark inside tube at 5/8"
-4.2 Glue Tube
-4.2.1 Measure inside rear of body tube to 1 3/4' position on tube
-4.2.2 Use finger to smear glue 1 3/4" inside rear of body tube along LL.
-4.3 Assemble Engine Hook
-4.3.1 Align engine hook with LL line
-4.3.2 Insert engine mount into body tube until centering ring is even w/the 5/8" glue mark
-4.3.3 Let Dry
-4.4 Gluing Center Body Ring
-4.4.1 Locate scrap piece of balsa to apply glue
-4.4.2 Apply glue to centering/body tube joint
-4.4.3 Let Dry
5.0 ATTACH FINS
-5.1 Attach Fin #1
-5.1.1 Apply thin layer of glue to edge of fin
-5.1.2 Allow to dry (1 minute for model)
-5.1.3 Apply second layer of glue to edge of fin
-5.1.4 Attach Fin to body tube along one of fin lines flush w/end
-5.2 Attach Fin #2
-5.2.1 Apply thin layer of glue to edge of fin#2
-5.2.2 Allow to dry (1 minute for model)
-5.2.3 Apply second layer of glue to edge of fin #2
-5.2.4 Attach Fin #2 to body tube along one of fin lines flush w/end
-5.3 Attach Fin #3
-5.3.1 Apply thin layer of glue to edge of fin #3
-5.3.2 Allow to dry (1 minute for model)
-5.3.3 Apply second layer of glue to edge of fin #3
-5.3.4 Attach Fin #3 to body tube along one of fin lines flush w/end
-5.4 Attach Fin #4
-5.4.1 Apply thin layer of glue to edge of fin #4
-5.4.2 Allow to dry (1 minute for model)
-5.4.3 Apply second layer of glue to edge of fin #4
-5.4.4 Attach Fin #4 to body tube along one of fin lines flush w/end
-5.5 Check Fin Alignment
-5.5.1 Check Fin #1 Alignment as shown in diagram
-5.5.2 Check Fin #2 Alignment as shown in diagram
-5.5.3 Check Fin #3 Alignment as shown in diagram
-5.5.4 Check Fin #4 Alignment as shown in diagram
-5.6 Allow glue to dry
-5.6.1 Let Glue Set
-5.6.2 Stand Rocket on end
-5.6.3 let glue dries completely
6.0 ATTACH SHOCK CORD
-6.1 Cut out shock cord mount
-6.1.1 Cut out shock cord from front page
-6.2 First Glue Application
-6.2.1 Attach shock cord to shock cord mount
-6.2.2 Apply glue to shock cord mount
-6.2.3 Fold edge of shock cord mount forward over glued shock cord
-6.3 Second Glue Application
-6.3.1 Apply glue to shock cord mount
-6.3.2 Fold forward again-see diagram for clarification
-6.4 Squueze and Hold
-6.4.1 Squeeze shock cord/shock cord mount tightly
-6.4.2 Hold for 1 minute
-6.5 Attaching Shock Cord Mount
-6.5.1 Glue mount 1" inside body tube
-6.5.2 Hold until glue sets
-6.5.3 Let Dry Completely
7.0 ASSEMBLE NOSE CONE
-7.1 Glue nose cone
-7.1.1 Apply plastic cememt to inside rim of nose cone
-7.1.2 Press Nose Cone Insert into place over plastic cement inside of nose cone rim
-7.1.3 Let Dry Completely
8.0 ATTACH PARACHUTE/SHOCK CORD
-8.1 Attach Lines
-8.1.1 Pass shroud line on parachute through eyelit
-8.2 Attach Parachute
-8.2.1 Pass parachute through loop in shroud-look to diagram for clarification
-8.3 Tie Lines
-8.3.1 Tie shock cord to nose cone using a double knot
9.0 ATTACH LAUNCH LUG
-9.1 Glue launch lines
-9.1.1 Glue LL centerd onto LL Line on rocket body
-9.2 Application of Glue Fillets
-9.2.1 Apply glue fillets along launch lug
-9.2.2 Apply glue fillets along fin/body tube joints
-9.2.3 Smooth each fillet with finger
-9.2.4 Let glue dry completely
10.0 PAINTING THE ROCKET
-10.1 Apply first coat
-10.1.1 Spray rocket with white primer
-10.1.2 Let Dry
-10.2 Sand
-10.1.2 Sand entire rocket
-10.3 Apply final coat
-10.3.1 Spray completed rocket with white second coat of primer
-10.3.2 Let Dry
-10.3.3 Spray Nose Cone with Copper paint
-10.3.4 Let Dry
11.0 APPLICATION OF DECALS
-11.1 Apply first decal
-11.1.1 Remove First decal from back sheet
-11.1.2 Place on Rocket where indicated
-11.1.3 Rub decal to remove bubbles
-11.2 Apply second decal
-11.2.1 Remove second decal from backing sheet
-11.2.2 Place on Rocket where indicated
-11.2.3 Rub decal to remove bubbles
-11.3 Apply third decal
-11.3.1 Remove third decal from backing sheet
-11.3.2 Place on Rocket where indicated
-11.3.3 Rub decal to remove bubbles
-11.4 Apply fourth decal
-11.4.1 Remove fourth decal from backing sheet
-11.4.2 Place on Rocket where indicated
-11.4.3 Rub decal to remove bubbles
-11.5 Apply fifth decal
-11.5.1 Remove fifth decal from backing sheet
-11.5.2 Place on Rocket where indicated
-11.5.3 Rub decal to remove bubbles
-11.6 Apply sixth Decal
-11.6.1 Remove sixth decal from backing sheet
-11.6.2 Place on Rocket where indicated
-11.6.3 Rub decal to remove bubbles
-11.7 Apply seventh Decal
-11.7.1 Remove seventh decal from backing sheet
-11.7.2 Place on Rocket where indicated
-11.7.3 Rub decal to remove bubbles
12.0 APPLYING CLEAR COAT
-12.1 Apply clear coat to entire rocket
12.1.1 Apply clear coat to entire rocket
12.1.2 Dry Completely
13.0 DISPLAY NOZZLE ASSEMBLY
-13.1 Spray Nozzle Base White
-13.1.1 Paint Nozzle #1 w/Silver Paint Pen
-13.1.2 Paint Nozzle #2 w/ Silver Paint Pen
-13.1.3 Paint Nozzle #3 w/ Silver Paint Pen
-13.1.4 Paint Nozzle #4 w/ Silver Paint Pen
-13.1.5 Allow to dry
-13.2 Apply Glue
-13.2.1 Apply glue to tab on nozzle #1
-13.2.2 Place Nozzle #1 into hole on base
-13.2.3 Apply glue to tab on nozzle #2
-13.2.4 Place Nozzle #2 into hole on base
-13.2.5 Apply glue to tab on nozzle #3
-13.2.6 Place Nozzle #3 into hole on base
-13.2.7 Apply glue to tab on nozzle #4
-13.2.8 Place Nozzle #4 into hole on base
14.0 ROCKET PREFLIGHT
14.1 prepare
-14.1.1 Remove Nose Cone from Rocket
-14.1.2 Locate recovery wadding
-14.1.3 Insert 4-5 loosely crumpled squares of recovery wadding
14.2 Spike
-14.2.1 Pull parachute into a spike-see diagram for clarification
14.3 Fold
-14.3.1 Fold parachute according to diagram
14.4 Roll
-14.4.1 Roll parachute according to diagram
14.5 Re-insert
-14.5.1 Wrap lines loosly around rolled parachute-see diagram for clarification
-14.5.2 Insert parachute into body tube of rocket
-14.5.3 Insert shock cord into body tube of rocket
-14.5.4 Insert nose cone into body tube of rocket
15.0 PREPARE FOR TEST LAUNCH
-15.1 Insert Engine
-15.1.1 Remove engine
-15.1.2 Insert tip to touch propellant
-15.1.3 Insert engine into rocket

Decomposed WBS

1.0 ASSEMBLE ENGINE MOUNT
1.1 Measure, Mark and Cut Engine Tube "
1.1.1 Lay ruler along engine tube
1.1.2 Measure engine from left of engine tube @ 1/8"""
1.1.3 Mark left end of engine Tube @ 1/8'
1.1.4 Measure engine from left of engine tube @ 3/4"""
1.1.5 Mark from left of engine tube @ 3/4"" "
1.1.6 Measure engine tube from left of engine tube @ 11/2"""
1.1.7 Mark from left of engine tube @ 1 1/2"""
1.2 Cut Engine Tube
1.2.1 Cut Slit of 1/8"" @ 1 1/2 inch Mark on Engine Tube"
1.3 Glue, Tube, Assemble Hook "
1.3.1 Apply thin line of glue completely around engine at 3/4"" mark"
1.3.2 Position Hook per diagram
1.3.3 Insert Engine Hook into 1/8"" Slit on Engine Mount Tube"
1.4 Assemble Mylar Ring to Tube
1.4.1 Slide Mylar ring onto Engine Mount tube at 3/4"" mark "
1.4.2 Let Dry
1.5 Assemble Yellow Engine Block to Engine Mount Tube
1.5.1 Apply glue inside front of Engine Mount tube
1.5.2 Insert Yellow Engine Block flush with the right end per diagram
1.5.3 Let Dry
1.6 Assemble Centering Rings
1.6.1 Remove Centering rings from card with modeling knife
1.6.2 Apply thin line of Glue around engine mount tube @ 1/8"" mark"
1.6.3 Slide notched Centering Ring onto glued line @ 1/8"" mark"
1.6.4 Let Glue Set
1.6.5 Apply thin line of Glue to opposite side of notched center ring flush with end of engine mount tube
1.6.6 Slide un-notched Centering Ring in place over glue flush with end of engine tube mount
1.6.7 Let Dry
1.7 Application of Glue Fillets
1.7.1 Apply Glue Fillets to both sides of Centering Rings for reinforcement
1.7.2 Let Dry
2.0 FIN PREPARATION
2.1 Sand/Cut fins
2.1.1 Sand Laser Cut Balsa Sheet w/Fine Sandpaper
2.2 Cutting Out Fins
2.2.1 Cut out fin #1 w/modeling knife
2.2.2 Cut out fin #2 w/modeling knife
2.2.3 Cut out fin #3 w/ modeling knife
2.2.4 Cut out fin #4 w/modeling knife
2.3 Stack and Sand Fins
2.3.1 Stack Fins
2.3.2 Sand Edges of fins
3.0 MARK FIN AND LAUNCH LUG LINES
3.1 Cut - Tape
3.1.1 Cut out tube marking guide
3.1.2 Tape tube marking guide around body tube
3.1.3 Mark body tube at arrows
3.1.4 Mark Launch Lug Line as LL on Body tube
3.2 Remove guide, connect fins and lug lines, extend LL line"
3.2.1 Remove Tube Marking guide from body tube
3.2.2 Connect Fins using door frame
3.2.3 Connect launch lug lines using door frame
3.3 Extend Launch Lug Line
3.3.1 Extend launch lug line 3 3/4"" from end of tube"
4.0 INSERTING ENGINE MOUNT
4.1 Mark inside of tube @ 5/8"" where LL is"
4.1.1 Measure inside tube to 5/8"" position on tube"
4.1.2 Mark inside tube at 5/8"""
4.2 Glue Tube
4.2.1 Measure inside rear of body tube to 1 3/4' position on tube
4.2.2 Use finger to smear glue 1 3/4"" inside rear of body tube along LL."
4.3 Assemble Engine Hook
4.3.1 Align engine hook with LL line
4.3.2 Insert engine mount into body tube until centering ring is even w/the 5/8"" glue mark"
4.3.3 Let Dry
4.4 Gluing Center Body Ring
4.4.1 Locate scrap piece of balsa to apply glue
4.4.2 Apply glue to centering/body tube joint
4.4.3 Let Dry
5.0 ATTACH FINS
5.1 Attach Fin #1
5.1.1 Apply thin layer of glue to edge of fin
5.1.2 Allow to dry (1 minute for model)
5.1.3 Apply second layer of glue to edge of fin
5.1.4 Attach Fin to body tube along one of fin lines flush w/end
5.2 Attach Fin #2
5.2.1 Apply thin layer of glue to edge of fin#2
5.2.2 Allow to dry (1 minute for model)
5.2.3 Apply second layer of glue to edge of fin #2
5.2.4 Attach Fin #2 to body tube along one of fin lines flush w/end
5.3 Attach Fin #3
5.3.1 Apply thin layer of glue to edge of fin #3
5.3.2 Allow to dry (1 minute for model)
5.3.3 Apply second layer of glue to edge of fin #3
5.3.4 Attach Fin #3 to body tube along one of fin lines flush w/end
5.4 Attach Fin #4
5.4.1 Apply thin layer of glue to edge of fin #4
5.4.2 Allow to dry (1 minute for model)
5.4.3 Apply second layer of glue to edge of fin #4
5.4.4 Attach Fin #4 to body tube along one of fin lines flush w/end
5.5 Check Fin Alignment
5.5.1 Check Fin #1 Alignment as shown in diagram
5.5.2 Check Fin #2 Alignment as shown in diagram
5.5.3 Check Fin #3 Alignment as shown in diagram
5.5.4 Check Fin #4 Alignment as shown in diagram
5.6 Allow glue to dry
5.6.1 Let Glue Set
5.6.2 Stand Rocket on end
5.6.3 let glue dries completely
6.0 ATTACH SHOCK CORD
6.1 Cut out shock cord mount
6.1.1 Cut out shock cord from front page
6.2 First Glue Application
6.2.1 Attach shock cord to shock cord mount
6.2.2 Apply glue to shock cord mount
6.2.3 Fold edge of shock cord mount forward over glued shock cord
6.3 Second Glue Application
6.3.1 Apply glue to shock cord mount
6.3.2 Fold forward again-see diagram for clarification
6.4 Squeeze and Hold
6.4.1 Squeeze shock cord/shock cord mount tightly
6.4.2 Hold for 1 minute
6.5 Attaching Shock Cord Mount
6.5.1 Glue mount 1"" inside body tube"
6.5.2 Hold until glue sets
6.5.3 Let Dry Completely
7.0 ASSEMBLE NOSE CONE
7.1 Glue nose cone
7.1.1 Apply plastic cement to inside rim of nose cone
7.1.2 Press Nose Cone Insert into place over plastic cement inside of nose cone rim
7.1.3 Let Dry Completely
8.0 ATTACH PARACHUTE/SHOCK CORD
8.1 Attach Lines
8.1.1 Pass shroud line on parachute through eyelet
8.2 Attach Parachute
8.2.1 Pass parachute through loop in shroud-look to diagram for clarification
8.3 Tie Lines
8.3.1 Tie shock cord to nose cone using a double knot
9.0 ATTACH LAUNCH LUG
9.1 Glue launch lines
9.1.1 Glue LL centered onto LL Line on rocket body
9.2 Application of Glue Fillets
9.2.1 Apply glue fillets along launch lug
9.2.2 Apply glue fillets along fin/body tube joints
9.2.3 Smooth each fillet with finger
9.2.4 Let glue dry completely
10.0 PAINTING THE ROCKET
10.1 Apply first coat
10.1.1 Spray rocket with white primer
10.1.2 Let Dry
10.2 Sand
10.1.2 Sand entire rocket
10.3 Apply final coat
10.3.1 Spray completed rocket with white second coat of primer
10.3.2 Let Dry
10.3.3 Spray Nose Cone with Copper paint
10.3.4 Let Dry
11.0 APPLICATION OF DECALS
11.1 Apply first decal
11.1.1 Remove First decal from back sheet
11.1.2 Place on Rocket where indicated
11.1.3 Rub decal to remove bubbles
11.2 Apply second decal
11.2.1 Remove second decal from backing sheet
11.2.2 Place on Rocket where indicated
11.2.3 Rub decal to remove bubbles
11.3 Apply third decal
11.3.1 Remove third decal from backing sheet
11.3.2 Place on Rocket where indicated
11.3.3 Rub decal to remove bubbles
11.4 Apply fourth decal
11.4.1 Remove fourth decal from backing sheet
11.4.2 Place on Rocket where indicated
11.4.3 Rub decal to remove bubbles
11.5 Apply fifth decal
11.5.1 Remove fifth decal from backing sheet
11.5.2 Place on Rocket where indicated
11.5.3 Rub decal to remove bubbles
11.6 Apply sixth Decal
11.6.1 Remove sixth decal from backing sheet
11.6.2 Place on Rocket where indicated
11.6.3 Rub decal to remove bubbles
11.7 Apply seventh Decal
11.7.1 Remove seventh decal from backing sheet
11.7.2 Place on Rocket where indicated
11.7.3 Rub decal to remove bubbles
12.0 APPLYING CLEAR COAT
12.1 Apply clear coat to entire rocket
12.1.1 Apply clear coat to entire rocket
12.1.2 Dry Completely
13.0 DISPLAY NOZZLE ASSEMBLY
13.1 Spray Nozzle Base White
13.1.1 Paint Nozzle #1 w/Silver Paint Pen
13.1.2 Paint Nozzle #2 w/ Silver Paint Pen
13.1.3 Paint Nozzle #3 w/ Silver Paint Pen
13.1.4 Paint Nozzle #4 w/ Silver Paint Pen
13.1.5 Allow to dry
13.2 Apply Glue
13.2.1 Apply glue to tab on nozzle #1
13.2.2 Place Nozzle #1 into hole on base
13.2.3 Apply glue to tab on nozzle #2
13.2.4 Place Nozzle #2 into hole on base
13.2.5 Apply glue to tab on nozzle #3
13.2.6 Place Nozzle #3 into hole on base
13.2.7 Apply glue to tab on nozzle #4
13.2.8 Place Nozzle #4 into hole on base
14.0 ROCKET PREFLIGHT
14.1 Prepare Rocket for Preflight
14.1.1 Remove Nose Cone from Rocket
14.1.2 Locate recovery wadding
14.1.3 Insert 4-5 loosely crumpled squares of recovery wadding
14.2 Spike
14.2.1 Pull parachute into a spike-see diagram for clarification
14.3 Fold
14.3.1 Fold parachute according to diagram
14.4 Roll
14.4.1 Roll parachute according to diagram
14.5 Re-insert
14.5.1 Wrap lines loosely around rolled parachute-see diagram for clarification
14.5.2 Insert parachute into body tube of rocket
14.5.3 Insert shock cord into body tube of rocket
14.5.4 Insert nose cone into body tube of rocket
15.0 PREPARE FOR TEST LAUNCH
15.1 Insert Engine
15.1.1 Remove engine
15.1.2 Insert tip to touch propellant
15.1.3 Insert engine into rocket

Cost Estimate

Resource types - estimates in man-hours for Duration Estimate
TASKS Fitter Draftsman Gluer Cutter SanderI SanderII Painter I Painter II Engineer Dummy
1.0 ASSEMBLE ENGINE MOUNT 14 30 7 4 0 0 0 0 0 40 95
1.1 Measure, Mark and Cut Engine Tube " 5 30 0 0 0 0 0 0 0 0
1.1.1 Lay ruler along engine tube 5
1.1.2 Measure engine from left of engine tube @ 1/8""" 5
1.1.3 Mark left end of engine Tube @ 1/8' 5
1.1.4 Measure engine from left of engine tube @ 3/4""" 5
1.1.5 Mark from left of engine tube @ 3/4"" " 5
1.1.6 Measure engine tube from left of engine tube @ 11/2""" 5
1.1.7 Mark from left of engine tube @ 1 1/2""" 5
1.2 Cut Engine Tube 0 0 0 2 0 0 0 0 0 0
1.2.1 Cut Slit of 1/8"" @ 1 1/2 inch Mark on Engine Tube" 2
1.3 Glue, Tube, Assemble Hook " 5 0 2 0 0 0 0 0 0 0
1.3.1 Apply thin line of glue completely around engine at 3/4"" mark" 2
1.3.2 Position Hook per diagram 2
1.3.3 Insert Engine Hook into 1/8"" Slit on Engine Mount Tube" 3
1.4 Assemble Mylar Ring to Tube 1 0 0 0 0 0 0 0 0 8
1.4.1 Slide Mylar ring onto Engine Mount tube at 3/4"" mark " 1
1.4.2 Let Dry 8
1.5 Assemble Yellow Engine Block to Engine Mount Tube 1 0 1 0 0 0 0 0 0 8
1.5.1 Apply glue inside front of Engine Mount tube 1
1.5.2 Insert Yellow Engine Block flush with the right end per diagram 1
1.5.3 Let Dry 8
1.6 Assemble Centering Rings 2 0 2 2 0 0 0 0 0 16
1.6.1 Remove Centering rings from card with modeling knife 2
1.6.2 Apply thin line of Glue around engine mount tube @ 1/8"" mark" 1
1.6.3 Slide notched Centering Ring onto glued line @ 1/8"" mark" 1
1.6.4 Let Glue Set 8
1.6.5 Apply thin line of Glue to opposite side of notched center ring flush with end of engine mount tube 1
1.6.6 Slide un-notched Centering Ring in place over glue flush with end of engine tube mount 1
1.6.7 Let Dry 8
1.7 Application of Glue Fillets 0 0 2 0 0 0 0 0 0 8
1.7.1 Apply Glue Fillets to both sides of Centering Rings for reinforcement 2
1.7.2 Let Dry 8
2.0 FIN PREPARATION 2 0 0 12 16 0 0 0 0 0 30
2.1 Sand/Cut fins 0 0 0 0 8 0 0 0 0 0
2.1.1 Sand Laser Cut Balsa Sheet w/Fine Sandpaper 8
2.2 Cutting Out Fins 0 0 0 12 0 0 0 0 0 0
2.2.1 Cut out fin #1 w/modeling knife 3
2.2.2 Cut out fin #2 w/modeling knife 3
2.2.3 Cut out fin #3 w/ modeling knife 3
2.2.4 Cut out fin #4 w/modeling knife 3
2.3 Stack and Sand Fins 2 0 0 0 8 0 0 0 0 0
2.3.1 Stack Fins 2
2.3.2 Sand Edges of fins 8
3.0 MARK FIN AND LAUNCH LUG LINES 19 12 0 2 0 0 0 0 0 0 33
3.1 Cut - Tape 3 8 0 2 0 0 0 0 0 0
3.1.2 Cut out tube marking guide 2
3.1.2 Tape tube marking guide around body tube 3
3.1.3 Mark body tube at arrows 4
3.1.4 Mark Launch Lug Line as LL on Body tube 4
3.2 Remove guide, connect fins and lug lines, extend LL line" 16 0 0 0 0 0 0 0 0 0
3.2.1 Remove Tube Marking guide from body tube 4
3.2.2 Connect Fins using door frame 4
3.2.3 Connect launch lug lines using door frame 8
3.3 Extend Launch Lug Line 0 4 0 0 0 0 0 0 0 0
3.3.1 Extend launch lug line 3 3/4"" from end of tube" 4
4.0 INSERTING ENGINE MOUNT 11 10 6 0 0 0 0 0 0 16 43
4.1 Mark inside of tube @ 5/8"" where LL is" 0 7 0 0 0 0 0 0 0 0
4.1.1 Measure inside tube to 5/8"" position on tube" 4
4.1.2 Mark inside tube at 5/8""" 3
4.2 Glue Tube 0 3 2 0 0 0 0 0 0 0
4.2.1 Measure inside rear of body tube to 1 3/4' position on tube 3
4.2.2 Use finger to smear glue 1 3/4"" inside rear of body tube along LL." 2
4.3 Assemble Engine Hook 10 0 0 0 0 0 0 0 0 8
4.3.1 Align engine hook with LL line 5
4.3.2 Insert engine mount into body tube until centering ring is even w/the 5/8"" glue mark" 5
4.3.3 Let Dry 8
4.4 Gluing Center Body Ring 1 0 4 0 0 0 0 0 0 8
4.4.1 Locate scrap piece of balsa to apply glue 1
4.4.2 Apply glue to centering/body tube joint 4
4.4.3 Let Dry 8
5.0 ATTACH FINS 20 16 20 0 0 0 0 0 0 17 73
5.1 Attach Fin #1 4 0 5 0 0 0 0 0 0 1
5.1.1 Apply thin layer of glue to edge of fin 3
5.1.2 Allow to dry (1 minute for model) 1
5.1.3 Apply second layer of glue to edge of fin 2
5.1.4 Attach Fin to body tube along one of fin lines flush w/end 4
5.2 Attach Fin #2 4 0 5 0 0 0 0 0 0 1
5.2.1 Apply thin layer of glue to edge of fin#2 3
5.2.2 Allow to dry (1 minute for model) 1
5.2.3 Apply second layer of glue to edge of fin #2 2
5.2.4 Attach Fin #2 to body tube along one of fin lines flush w/end 4
5.3 Attach Fin #3 4 0 5 0 0 0 0 0 0 1
5.3.1 Apply thin layer of glue to edge of fin #3 3
5.3.2 Allow to dry (1 minute for model) 1
5.3.3 Apply second layer of glue to edge of fin #3 2
5.3.4 Attach Fin #3 to body tube along one of fin lines flush w/end 4
5.4 Attach Fin #4 4 0 5 0 0 0 0 0 0 1
5.4.1 Apply thin layer of glue to edge of fin #4 3
5.4.2 Allow to dry (1 minute for model) 1
5.4.3 Apply second layer of glue to edge of fin #4 2
5.4.4 Attach Fin #4 to body tube along one of fin lines flush w/end 4
5.5 Check Fin Alignment 0 16 0 0 0 0 0 0 0 0
5.5.1 Check Fin #1 Alignment as shown in diagram 4
5.5.2 Check Fin #2 Alignment as shown in diagram 4
5.5.3 Check Fin #3 Alignment as shown in diagram 4
5.5.4 Check Fin #4 Alignment as shown in diagram 4
5.6 Allow glue to dry 4 0 0 0 0 0 0 0 0 13
5.6.1 Let Glue Set 5
5.6.2 Stand Rocket on end 4
5.6.3 let glue dries completely 8
6.0 ATTACH SHOCK CORD 16 0 19 5 0 0 0 0 0 8 48
6.1 Cut out shock cord mount 0 0 0 5 0 0 0 0 0 0
6.1.1 Cut out shock cord from front page 5
6.2 First Glue Application 8 0 4 0 0 0 0 0 0 0
6.2.1 Attach shock cord to shock cord mount 4
6.2.2 Apply glue to shock cord mount 4
6.2.3 Fold edge of shock cord mount forward over glued shock cord 4
6.3 Second Glue Application 4 0 4 0 0 0 0 0 0 0
6.3.1 Apply glue to shock cord mount 4
6.3.2 Fold forward again-see diagram for clarification 4
6.4 Squeeze and Hold 0 0 6 0 0 0 0 0 0 0
6.4.1 Squeeze shock cord/shock cord mount tightly 2
6.4.2 Hold for 1 minute 4
6.5 Attaching Shock Cord Mount 4 0 5 0 0 0 0 0 0 8
6.5.1 Glue mount 1"" inside body tube" 4 4
6.5.2 Hold until glue sets 1
6.5.3 Let Dry Completely 8
7.0 ASSEMBLE NOSE CONE 4 0 4 0 0 0 0 0 0 8 16
7.1 Glue nose cone 4 0 4 0 0 0 0 0 0 8
7.1.1 Apply plastic cement to inside rim of nose cone 4
7.1.2 Press Nose Cone Insert into place over plastic cement inside of nose cone rim 4
7.1.3 Let Dry Completely 8
8.0 ATTACH PARACHUTE/SHOCK CORD 18 0 0 0 0 0 0 0 0 0 18
8.1 Attach Lines 7 0 0 0 0 0 0 0 0 0
8.1.1 Pass shroud line on parachute through eyelet 7
8.2 Attach Parachute 5 0 0 0 0 0 0 0 0 0
8.2.1 Pass parachute through loop in shroud-look to diagram for clarification 5
8.3 Tie Lines 6 0 0 0 0 0 0 0 0 0
8.3.1 Tie shock cord to nose cone using a double knot 6
9.0 ATTACH LAUNCH LUG 0 0 24 0 0 0 0 0 0 8 32
9.1 Glue launch lines 0 0 4 0 0 0 0 0 0 0
9.1.1 Glue LL centered onto LL Line on rocket body 4
9.2 Application of Glue Fillets 0 0 20 0 0 0 0 0 0 8
9.2.1 Apply glue fillets along launch lug 4
9.2.2 Apply glue fillets along fin/body tube joints 12
9.2.3 Smooth each fillet with finger 4
9.2.4 Let glue dry completely 8
10.0 PAINTING THE ROCKET 0 0 0 0 1 16 8 48 0 24 97
10.1 Apply first coat 0 0 0 0 0 0 8 0 0 8
10.1.1 Spray rocket with white primer 8
10.1.2 Let Dry 8
10.2 Sand 0 0 0 0 1 16 0 0 0 0
10.1.2 Sand entire rocket 1 16
10.3 Apply final coat 0 0 0 0 0 0 0 48 0 16
10.3.1 Spray completed rocket with white second coat of primer 16
10.3.2 Let Dry 8
10.3.3 Spray Nose Cone with Copper paint 32
10.3.4 Let Dry 8
11.0 APPLICATION OF DECALS 0 35 0 0 0 0 0 0 0 0 35
11.1 Apply first decal 0 5 0 0 0 0 0 0 0 0
11.1.1 Remove First decal from back sheet 1
11.1.2 Place on Rocket where indicated 3
11.1.3 Rub decal to remove bubbles 1
11.2 Apply second decal 0 5 0 0 0 0 0 0 0 0
11.2.1 Remove second decal from backing sheet 1
11.2.2 Place on Rocket where indicated 3
11.2.3 Rub decal to remove bubbles 1
11.3 Apply third decal 0 5 0 0 0 0 0 0 0 0
11.3.1 Remove third decal from backing sheet 1
11.3.2 Place on Rocket where indicated 3
11.3.3 Rub decal to remove bubbles 1
11.4 Apply fourth decal 0 5 0 0 0 0 0 0 0 0
11.4.1 Remove fourth decal from backing sheet 1
11.4.2 Place on Rocket where indicated 3
11.4.3 Rub decal to remove bubbles 1
11.5 Apply fifth decal 0 5 0 0 0 0 0 0 0 0
11.5.1 Remove fifth decal from backing sheet 1
11.5.2 Place on Rocket where indicated 3
11.5.3 Rub decal to remove bubbles 1
11.6 Apply sixth Decal 0 5 0 0 0 0 0 0 0 0
11.6.1 Remove sixth decal from backing sheet 1
11.6.2 Place on Rocket where indicated 3
11.6.3 Rub decal to remove bubbles 1
11.7 Apply seventh Decal 0 5 0 0 0 0 0 0 0 0
11.7.1 Remove seventh decal from backing sheet 1
11.7.2 Place on Rocket where indicated 3
11.7.3 Rub decal to remove bubbles 1
12.0 APPLYING CLEAR COAT 0 0 0 0 0 0 0 8 0 8 16
12.1 Apply clear coat to entire rocket 0 0 0 0 0 0 0 8 0 8
12.1.1 Apply clear coat to entire rocket 8
12.1.2 Dry Completely 8
13.0 DISPLAY NOZZLE ASSEMBLY 8 0 8 0 0 0 9 0 0 8 33
13.1 Spray Nozzle Base White 0 0 0 0 0 0 9 0 0 8
13.1.1 Paint Nozzle #1 w/Silver Paint Pen 2
13.1.2 Paint Nozzle #2 w/ Silver Paint Pen 2
13.1.3 Paint Nozzle #3 w/ Silver Paint Pen 2
13.1.4 Paint Nozzle #4 w/ Silver Paint Pen 3
13.1.5 Allow to dry 8
13.2 Apply Glue 8 0 8 0 0 0 0 0 0 0
13.2.1 Apply glue to tab on nozzle #1 2
13.2.2 Place Nozzle #1 into hole on base 2
13.2.3 Apply glue to tab on nozzle #2 2
13.2.4 Place Nozzle #2 into hole on base 2
13.2.5 Apply glue to tab on nozzle #3 2
13.2.6 Place Nozzle #3 into hole on base 2
13.2.7 Apply glue to tab on nozzle #4 2
13.2.8 Place Nozzle #4 into hole on base 2
14.0 ROCKET PREFLIGHT 42 0 0 0 0 0 0 0 0 0 42
14.1 Prepare Rocket for Preflight 13 0 0 0 0 0 0 0 0 0
14.1.1 Remove Nose Cone from Rocket 6
14.1.2 Locate recovery wadding 1
14.1.3 Insert 4-5 loosely crumpled squares of recovery wadding 6
14.2 Spike 4 0 0 0 0 0 0 0 0 0
14.2.1 Pull parachute into a spike-see diagram for clarification 4
14.3 Fold 4 0 0 0 0 0 0 0 0 0
14.3.1 Fold parachute according to diagram 4
14.4 Roll 4 0 0 0 0 0 0 0 0 0
14.4.1 Roll parachute according to diagram 4
14.5 Re-insert 17 0 0 0 0 0 0 0 0 0
14.5.1 Wrap lines loosely around rolled parachute-see diagram for clarification 5
14.5.2 Insert parachute into body tube of rocket 6
14.5.3 Insert shock cord into body tube of rocket 2
14.5.4 Insert nose cone into body tube of rocket 4
15.0 PREPARE FOR TEST LAUNCH 0 0 0 0 0 0 0 0 32 0 32
15.1 Insert Engine 0 0 0 0 0 0 0 0 32 0
15.1.1 Remove engine 10
15.1.2 Insert tip to touch propellant 10
15.1.3 Insert engine into rocket 12
RESOURCE TOTALS 154 103 88 23 17 16 17 56 32 137 643
Add resource totals as cross check 643
RESOURCE HOURLY RATES $50.00 $40.00 $25.00 $40.00 $25.00 $30.00 $25.00 $30.00 $55.00 $36 BLENDED RATES
RESOURCE COSTS $7,700.00 $4,120.00 $2,200.00 $920.00 $425.00 $480.00 $425.00 $1,680.00 $1,760.00 $19,710.00
Number Staff Hours
Week-1 40 27 18 19 16
Week-2 33 15 12 7
Week-3 6 5 3
Week-4 5 5 3
Week-5 20 16 20
Week-6 24
Week-7 1 16 8 48
Week-8 35
Week-9 8 8 9 8
Week-10 42
Week-11 32

Spend Plan-Baseline

CATEGORY Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 Week 12 Week 13 Week 14 Week 15 Week 16
Labor $21,600 $11,520 $4,320 $4,320 $4,320 $1,440 $5,760 $1,440 $5,760 $2,880 $1,440 $64,800
Material $15,685 $2,500 $5,800 $0 $0 $375 $270 $650 $1,875 $550 $50,000 $0 $0 $0 $0 $0 $77,705
Equipment / $1,025 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $1,025
parts
TOTAL $38,310 $14,020 $10,120 $4,320 $4,320 $1,815 $6,030 $2,090 $7,635 $3,430 $51,440 $0 $0 $0 $0 $0 $143,530
CUMULATIVE $38,310 $52,330 $62,450 $66,770 $71,090 $72,905 $78,935 $81,025 $88,660 $92,090 $143,530 $143,530 $143,530 $143,530 $143,530 $143,530
PROJECT BASELINE
EAC= $143,530
Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 38310 52330 62450 66770 71090 72905 78935 81025 88660 92090 143530

GANTT Schedule

Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 Week 12 Week 13 Week 14 Week 15 Week 16
1.0 ASSEMBLE ENGINE MOUNT
2.0 FIN PREPARATION
3.0 MARK FIN AND LAUNCH LUG LINES
4.0 INSERTING ENGINE MOUNT
5.0 ATTACH FINS
6.0 ATTACH SHOCK CORD
7.0 ASSEMBLE NOSE CONE
8.0 ATTACH PARACHUTE/SHOCK CORD
9.0 ATTACH LAUNCH LUG
10.0 PAINTING THE ROCKET
11.0 APPLICATION OF DECALS
12.0 APPLYING CLEAR COAT
13.0 DISPLAY NOZZLE ASSEMBLY
14.0 ROCKET PREFLIGHT
15.0 PREPARE FOR TEST LAUNCH

Network Diagram

0 95h 95
1: Assemble Engine Mount
0 0 95 95 43h 138 307 35h 342
4: Insert Engine Mount 11: Application of Decals
0 33h 33 95 0 138 138 73h 211 211 32h 243 307 0 342
3: Mark Fin & LL Lines 5: Attach Fins 9: Attach Launch Lug
138 0 211 211 0 243
342 16h 358
0 30h 30 12: Applying Clear Coat
2: Fin Preparation 342 0 358
108 108 138
0 44h 44 243 64h 307 358 42h 400
6: Attach Shock Cord 10: Painting the Rocket 14: Rocket Pre-Flight
196 196 240 44 3h 47 243 0 307 358 0 400
8: Attach Chute Shock Cord
0 16h 16 240 198 243
7: Assemble Nose Cone 400 32h 432
224 224 240 15: Prepare for Test Launch
400 0 432
0 32h 32
13: Display Nozzle Assembly
400 400 432 Legend
Early Start Duration Early Finish
Task Name
Late Start Slack Late Finish

M& E Forecast

Code Item Cost Week 1 Week 2 Week 3 Week 4 Week 5 Week 6 Week 7 Week 8 Week 9 Week 10 Week 11 Week 12 Week 13 Week 14 Week 15 Week 16
Equipment $1,025 $1,025 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0 $0
Scissors x 10 $100 $100
Pencil x10 $25 $25
Ruler x10 $50 $50
Modeling Knife x 5 $100 $100
Guide, Tube Marking $500 $500
Tool, Framing x 1 $125 $125
Tool, Fin Alignment x 1 $125 $125
Material $77,705 $15,685 $2,500 $5,800 $0 $0 $375 $270 $650 $1,875 $550 $50,000 $0 $0 $0 $0 $0
Guide, Shock Cord Mount $250 $250
Sand Paper (Course) $75 $75
Sand Paper (Fine) $75 $75
Glue $150 $150
Cement $120 $120
Tape, Masking $100 $100
Primer, Spray $110 $110
Paint, Spray (White) $160 $160
Paint, Spray (Clear) $125 $125
Pen, Paint (Silver) $250 $250
Tube, Body BT-58 $5,800 $5,800
Block, Engine EB-5B $5,000 $5,000
Cord, Shock, Rubber $115 $115
Hook, Mini Engine EH-3 $300 $300
Tube, Engine Mount BT-5 $500 $500
Ring, Retainer (Mylar) $250 $250
Sheet, Decal #60859 $650 $650
Card, Centering Ring RA5-58 $550 $550
Lug Launch LL-2A $375 $375
Fins, Laser Cut x4 $4,000 $4,000
Parachute Assembly 12' x 1 $2,500 $2,500
Base, Nozzle, Display x 1 $750 $750
Nozzles x 4 $1,000 $1,000
Cone, Nose x 1 $3,000 $3,000
Insert, Nose Cone x 1 $1,200 $1,200
Wadding, Recovery x 1pk $300 $300
Engine Assembly, A10-3T x 1 $50,000 $50,000
TOTAL $16,710 $2,500 $5,800 $0 $0 $375 $270 $650 $1,875 $550 $50,000 $0 $0 $0 $0 $0